Planning to change car oil? Here are some tips for a flawless process!

There is no better way available to prolong engine life and extend your loving car’s efficiency than with regular oil changes. This might appear rougher task than changing the spare parts though, but it’s something that any DIYer can do easily with a little guidance. Yet there are many folks doing it wrong, making it an ugly chore or overpaying for oil changes they could do themselves.

No matter how tough you find the process, this is one of the most important things you can do to keep your car running well, while saving a lot of your money. Over time, your oil will break down making your car oil filter clogged with contaminants. Well the time duration when you should change the oil depends upon your driving habits, type of vehicle, and kilometers run. Your vehicle may require oil change after every 3,000 miles. Time change of engine oil lets your car parts enjoy a longer life while increasing its performance to a great extent.

If you have no time to visit a local garage or are low on funds, then changing oil can be done yourself. For changing your vehicle oil, you don’t need to be an expert neurosurgeon. With doing it yourself you can start saving big bucks and you won’t be pressured into buying overpriced add-ons every time you go in for a change. Here we’ll show you how to change your oil fast and painlessly to ensure the longer life of your car oil filter and other engine parts. And we’ll show you some tips you may not know about.

Check the type & amount of oil required

This is something that many people avoid when changing the car engine oil, which ultimately leads to poor vehicle health. Knowing the type of oil required and the quantity plays a great role in prolonged engine life and smoother drive.

Before heading to an online auto parts store like Partsavatar Canada to buy supplies, consult the owner’s manual to confirm the type and amount of oil that’s required. Knowing the amount of oil required may be an easy task. For example, if you have a Ford Explorer car that requires 5.7 quarts, then go for 6. You might find the 5 quart containers to be tempting as they are cheaper, but they make it hard to pour oil steadily and are quite heavier. Also, don’t forget that the container will take a lot of shelf space.

Buy the right filter

Previously, oil filters were all pretty much the same inside. However the time has changed with a wide range of filters available for different vehicles from different manufacturers. Check the user manual recommendations and the time intervals for oil change (every 6,000 miles instead of 3,000 miles). If the time extends, you must buy a filter that is rated to go the distance. In short, don’t couple expensive oil with an economy filter—it won’t last.

Get together your tools and other supplies

Remember that oil changing isn’t something that can be done with just an oil container and oil filter. It requires a complete set of tools for example, oil-filter removal wrench, a drain pan and some gloves. You also need a jack to raise the car to gain access. For this kind of work, never use the flimsy jack that’s supplied with the car. Make sure to buy from a reliable store like Parts avatar Ontario.

Locate the drain plug and drain the oil

Once you are done with placing the jack on right location, it’s the time to locate the oil filter and drain plug. Usually almost every vehicle maker provides the drain plug at the bottom for easy draining of oil. When you prepare to drain the oil, make sure to place the drain pan under the drain plug – but not directly under it. If you are doing this outdoors, it’s good to account for wind. Tighten the plug once the used oil has been drained properly.

Change oil filter & add new oil

I assume you have already located the oil filter as guided above, now remove the oil filter. Don’t go too rough when removing the oil filter as it can break the filter free. Go slowly and switch to unscrewing the filter by hand as soon as you can. Install the new filter and tighten it to a satisfactory level.

Once you are done with the reconfirmation that the oil drain bolt and filter are both in place and properly tightened, add the new oil. Remember to add approximately one quart less than the recommended amount. For example, Ford Explorer requires 5.7 quarts. So you can add five and hold the last one back for later. The smaller size of bottle helps pour oil easily and steadily. Now, replace the oil cap and start the engine. Shut the engine after 30 seconds and check for any leaks.

Check the oil level

Once you are done with everything, check the oil level. If you short-filled it slightly then you can add some more oil. The only thing that is left now is to dispose of the old oil and filter. The local municipalities have household hazardous waste drop-off points so you can visit there for a safer disposal of the unwanted stuff. If you visit the local garage for oil change, they will take your waste oil at no charge.

You may also like...

Leave a Reply

Your email address will not be published. Required fields are marked *